Lg dlg5988w service manual

Table of Contents. Previous Page. Next Page. To avoid personal injury, disconnect power before servicing this product. If electrical power is required for diagnosis or test purposes, disconnect the power immediately after performing the necessary checks.

Page 8: Wire Connection : Direct Wire 4. Put the hooked shape ends of the wire under the screw of the terminal block hooked end facing rightward and squeeze the hook together and screw tightly. Put the hooked shaped ends of the other power supply cable wires under the outer terminal block screws hooked end facing right and squeeze the hooked ends together and screw tightly.

Page 9 Option 1: 3-Wire Connection with a Power Supply Cord lf your local codes or ordinances permit the connection of a frame-grounding conductor to the neutral wire, use these instructions. If your local codes or ordinances do not allow the connection of a frame-grounding conductor to the neutral wire, use the instructions under Section 3: Optional 3-wire connection.

Page 10 Option 2: 4-wire connection with a Power supply cord. Page 11 Option 3: Optional 3-wire connection. Remove center terminal block screw. Remove appliance neutral ground wire white from external ground connector screw. Page Gas Requirements Activating the Heater manually with the Door open may trip the Thermostat attached to the Heater, therefore do not activate it manually.

External ground connector c5 cm 2. Neutral grounding wire white c. Center silver-colored terminal block screw d. Neutral wire white or center wire e. Then, put the hooked shape end of the wire under the screw of the terminal block hooked end facing rightward and pinch the hook together and screw tightly.

If your local c codes or ordinances do not allow the connection of a frame-grounding conductor to the neutral wire, b use the instructions under Section 3: Optional d 3-wire connection. Neutral grounding wire white a. Center silver-colored terminal block screw b. Neutral wire white or center wire c.

Neutral prong e. Spade terminals with up turned ends e. Ring terminals g. Neutral white or center wire 3. Connect the other wires to outer terminal block 1. Loosen or remove center terminal block screw. Tighten screws. Connect neutral wire white or center wire of 4. Insert tab of terminal block cover into slot of terminal screw of the terminal block. Tighten dryer rear panel. Secure cover with hold-down screw. Green or bare copper wire of power supply cord c.

Ground prong f. Neutral wire white d. Neutral Prong e. Spade terminals with upturned ends f. Ring terminals 5. Connect the other wires to outer terminal block screws. Remove center terminal block screw. Remove appliance neutral ground wire white 6. Fasten it 7. Insert tab of terminal block cover into slot of under the center, silver colored terminal block dryer rear panel.

Center silver-colored terminal block screw c. White wire of harness. Connect ground wire green or bare of power supply cable to external ground conductor screw. Connect neutral wire white or center wire of power supply cord to the center, silver colored terminal screw of the terminal block.

Remove appliance neutral ground wire white from external ground connector screw. Neutral wire white or center wire d. Grounding path determined by a qualified electrician. Insert tab of terminal block cover into slot of dryer rear panel.

Connect a separate copper ground wire from the external ground connector screw to an adequate ground. For further assistance, refer to section on Gas Requirements. Make certain your dryer is equipped for use with the 3. Connect to gas supply pipe using a new flexible type of gas in your laundry room. Dryer is equipped stainless steel connector. Tighten all connections securely. Turn on gas and connection. Remove the shipping cap from the gas connection gas leaks with a non-corrosive leak detection fluid.

Make sure you do not 5. For L. Liquefied Petroleum gas connection, refer damage the pipe thread when removing the cap. Default Conditions of operation and termination. Default settings can be adjusted by users. Component Test Procedure Check result Remark 1.

N 2. Idler switch Measure resistance of the 1. Centrifugal switch Centrifugal switch Pull Drive forward. Activating the Heater manually with the Door open may trip the Thermostat attached to the Heater, therefore do not activate it manually.

Unit must be in Standby unit plugged in, display off 2. The display number is See test 4 below , in normal condition. If the door is closed. Proceed again from the step 1 all the way to the step 4. When measuring power, be sure to wear insulated gloves, to and avoid an Caution electric shock.

NO controller. Before measuring resistance, be sure to turn Power off, and do voltage discharge. Caution When discharging, contact the metal plug of Power cord with the Ground. Trouble Symptom During operation, Heater would not turn off, or remains on.

Difference between actual and sensed temperature is significant. From Thermistor assembly Connector. Air TEMP. Caution When discharging, contact the metal plug of Power cord with earth line. YES Relay check Measure while door is closed.

Measure while door is closed. YES from Not operating Lever is normal. NO Switch. Take 6pin Connector from the Controller. When contacting cloth to Electro load: 1. Is the measurement within the range of Table 2 during Diagnostic Test? Is the measurement within the range of Table 2 NO and Check.

Door Opening is not sensed. Drum motor will not operate. Display will flash at 0. Measure while Door is closed. When opening Measure while Door is open. Measure while Door is open. Check Controller. Check Harness-linking connector. While operating, Heating will not work. Trouble Symptom Drying time takes longer. NO Safety Thermostat. Check Motor. Check Harness-linking Connector. Caution When measuring power, be sure to wear insulated gloves, to avoid electric shock.

NO Hi limit Safety. Igniter operates? Conversion must be made by a qualified technician. Initially, Natural Gas mode is set. Propane Gas Orifice is on sale as a Service Part to authorized servicers only. Disassemble the pipe assembly. Replace Natural Gas orifice with Propane Gas orifice. Orifice Kit contents : Orifice Dia.

Remove 3 screws on the plate upper. Push the top plate 3. Open the top plate. Remove 2 screw on the control panel frame. Open the control panel assembly. Open the door assembly. Remove 2 screws. Remove 4 screws from upper side.

Disconnect the harness of door switch. Remove Cover Cabinet. Disconnect the door lamp and electro sensor connector. Remove 4 screws.

Disassemble the Tub Drum [Front]. Remove the Cover Cabinet and Tub drum [front]. Disengage belt from motor and idler pulleys. Carefully remove Drum out through front of dryer. Open the door. Remove the screw holding the drum lamp shield in place. Slide the shield up and remove. Remove the bulb and replace with a 15 watt, volt candelabra-base bulb.

Detach and remove the bottom, left or right side knockout as desired. Pre-assemble 4" elbow with 4" duct. Wrap duct tape around joint. Remove the filter. Remove 3 screws. Pull the grill. Disconnect electro sensor. Remove the Drum assembly. Remove 2 screws and cover Air guide.